Falcon Multirotors has made a long-range beast. The Raggio Lungo fits 6" props with the normal Hero mount, but with the Session mount, fits 7" props! This quad is made for long-range footage, screaming down a mountainside or shooting through a deep valley. You'll get Jello-free footage and zero props in view even with 1080P wide angle shots. The center of gravity is near perfect. Arms swaps are a breeze, just change two screws.
We carry the Session mount version which means the freedom to choose up to 7" props, giving you amazing flight times!
Designed by SFPV
We collaborated on every aspect of this frame with Colby Curtola, AKA SFPV. Colby wanted the ultimate long-range 6" quad, and we spent countless hours hashing out every possible detail to make it a reality.
Who says big frames have to be ugly?
Raggio was designed to be an efficient long-range workhorse, but we didn’t want to sacrifice function for form. Raggio's unique arms and camera mounts will make you proud to put the Raggio on your mantle after a hard day of flying. Imagine if a Lamborghini and a stealth attack helicopter had a baby; while that might be the stuff of beautiful nightmares, we think it would come out looking something like Raggio.
Multiple HD mount options
Although Raggio was designed specifically for the GoPro Hero 6 and 6" props, we also offer a mount for the more common GoPro Session that enables 7" props. With tear-resistant GoPro mounts that are printed on their side and a unique carbon plate sandwich that secures the TPU mount to the frame, your HD cam will never come off in a crash.
Roomy or lowrider, you choose.
Raggio ships with both 15 and 20mm standoffs, so you can slam your build with an AIO board or go roomy for stacks that include larger components, such as the TBS PowerCube Elite.
In both configurations, Raggio has ample room for a Unify and Crossfire, with no smashing or sandwiching required.
Not afraid to accessorize.
A host of accessories, such as booties, battery protectors, GoPro mounts, antenna mounts, and more are all available on Thingiverse.
- Wheelbase: 300mm
- Prop size: 6", 7" with Session
- Weight: 150g
- Arm Dimensions: 4.5mm thick, 10mm wide
- Stack height: 15-20mm
||Raggio supports 30.5mm FCs . We recommend using an AIO board to keep your stack low, maintaining the center of gravity of the design. As this frame was designed with long range in mind, you may want to consider using the Power Cube Elite Stack from Team Blacksheep. This bundle allows for plug and play TBS GPS and comes with a TBS Unify Pro HV built in for those 800mW flights!
||Most 20-35A ESCs will mount cleanly on the arms with no overhang. When built with the included 20mm standoffs, there is plenty of room in the center fuselage for a 4-in-1 ESC / FC stacks. Our recommended set up is a low kV motor running 6S LiPo, so make sure your ESC’s are 6S capable. We suggest using VHB between the ESC and the arm, then adding heat shrink to secure the ESC to the arms (leaving the motor pads accessible in case you need to swap motors).
||The ideal set up for long range rigs are lower kV motors that will pull fewer amps and give you plenty of flight time to reach the mountaintop.
||The Raggio was designed to carry a longer battery than we are used to with our super light race frames. Raggio is designed to mount the battery on the top, with slots for two battery straps giving you that extra bit of confidence that your battery will stay snug. There is plenty of width on the top plate for those fat 6S batteries that most top pilots are running on their long range rigs.
- CNHL 1500mAh 6S 100C
- Gensace 1800mAh 6S 60C
- PULSE 1800mAh 6S 45C
||Go Crossfire or failsafe trying.
||Raggio was designed around the RunCam Micro Swift, and the Foxeer Micro fits as well.
||We recommend using the TBS Unify Pro HV, due to its unrivaled reliability and ability to run at 800mW.